January 07, 2016
Autel MaxiDAS DS708 is a powerful scan tool that is able to customize many special settings. Following displays an example of activating BMW 7 series E65 Dynamic Drive/Active Roll Stabilization with DS708 automotive diagnostic scan tool.
What is Dynamic Drive?
Active Roll Stabilization (ARS) is an "active" suspension control system design to reduce body roll in cornering, resulting in improved handling. Dynamic Drive uses active stabilizers on the front and rear axles to counteract the vehicle's tendency to roll in a corner. Working together with acceleration and position sensors, a management system and other components, such as a compensation tank for sound control, the system ensures supreme agility at all speeds, balanced reactions to load changes and remarkably precise steering.
Autel MaxiDAS DS708 Instruction:
Well install DS708 diagnostic software
Connect Autel MaxiDASDS708 scanner with vehicle via OBD socket
Select vehicle region: European
Select vehicle make: BMW
Turn ignition OFF, wait about 10 seconds, turn ignition ON again
Select BMW series: 7 series
Select vehicle model: E65/E66/E68
Select detail vehicle model: 735i-N62-SAL
Select vehicle model version: EUR-LHD
Check and confirm your vehicle information
Select Services Function from Main group menu
Select Chassis control module
Select Dynamic Drive option
Select Startup
Select Start Startup
Follow the system prompts and accept the system notice
The control unit is currently carrying out an internal reset
Make sure there is fault code stored in ECU memory
Get on the car and test the result
Back to main program or exit the Autel DS708 scanner software program.
More information search: Autel Maxidas ds708
Posted by: UOBD2autel at
06:32 AM
| No Comments
| Add Comment
Post contains 265 words, total size 3 kb.
January 06, 2016
The tire pressure warning light blinks for 1 minute and stays on to indicate a tire pressure monitoring system malfunction after driving for about 20 minutes. If the ID code of the tire pressure warning valve and transmitter is not registered, the tire pressure warning system will not work properly. Following part are the detail instructions on resetting Toyota Camry (2007-2010) TPMS (Tire Pressure Monitoring System) indicator light withAutel MaxiDAS DS708 diagnostic scanner.
Instruction:
Autel DS708OBD2 diagnostic scan tool
Toyota Camry transmitter ID code
Ps: Where is the tire transmitter ID code located?
You need to copy the id code from the tire pressure sensor. It is stamped on the side of the sensor.)
Well install Autel DS708 software
Connect the DS708 scan tool with vehicle via OBD socket
Power on the device and browse to "System Menuâ€
Find out and locate "Tire Pressure Monitor†option in "System Menuâ€
Select Utility
Select ID Registration
The tire pressure warning valve and transmitter is equipped with a unique ID code. When replacing a tire pressure warning valve and transmitter, it is necessary to register the ID code.
Registration will fail if the time limit is exceeded for any step. Press OK to proceed.
Press OK to begin the registration process.
The system warns that you have 5 minutes to complete 3 procedures:
---Input each transmitter ID code
---Input next transmitter ID code
---Wait all ID code are registered.
Manually enter the transmitter ID follow the system prompts, and press OK
Step 4 of 4
Input the transmitter ID Code
Total Tires: 4
Register Tires:1
Press OK to input another ID Code.
Enter 4 ID codes one by one until the system will display ID Registration is complete message.
Go back to "Function Menuâ€, select "Read Codes†and then erase fault codes.
TPMS indicator light has been disabled. The indicator light on dashboard go off.
Posted by: UOBD2autel at
01:39 AM
| No Comments
| Add Comment
Post contains 319 words, total size 5 kb.
January 05, 2016
Autel MaxiDAS DS708 wireless diagnostic scan toolmakes throttle body relearning very easy without cutting wire. Here is the step-by-step instruction on the how reset GM ilde learn with ds708.
Instructions:
Well installMaxiDAS ds708diagnostic software.
Connect DS708 main unit with vehicle via USB or wireless connection.
Select vehicle model GMC YuKon (high idle speed issue) and year.
Select "Diagnostic Trouble Codes DTCs†on "Engine Control Module†menu to clear fault code.
Check there is no stored fault codes, back to select "Special Functions†on main menu.
Select Engine Speed/Throttle >> Engine Position.
AfterDS708well built communications, turn ignition ON with engine OFF, click OK.
You will be displayed the vehicle throttle body position information.
Select corresponding value that need to modified by clicking "Decrease†or "Increase†button on the right.
Page down to Engine control module program, select "Module setupâ€
Select "Idle Learn Resetâ€.
The system will display Idle Learn reset values, click "Reset†button on the left to reset.
Reset Ilde Learn complete, click OK to quit.
Check the vehicle throttle body condition.
Exit the Autel DS708 diagnostic software program.
So if you have any question aboutDs708 diagnostic scan tool,
More information searchWebsite:www.uobd2.net
Posted by: UOBD2autel at
03:20 AM
| No Comments
| Add Comment
Post contains 204 words, total size 4 kb.
January 04, 2016
OriginalAutel MaxiDAS DS708diagnostic scan toolhas a specific "Active Test†function menu where lots of functions are projected, like turn solenoids and injectors on and off, turn the fuel pump off etc.
Here is the instruction on doing an Nissan Xterra Active Test withAutel DS708OBDâ…¡diagnostic scanner.
Vehicle model:Nissan Xterra 2001
Well install DS708 diagnostic software
Connect the Autel DS708 main unit with vehicle via OBD socket
DS708 will do an "Auto Scan†which means it will automatically detect all engine control modules on the vehicle for diagnostic codes.
Make sure there is no fault codes stored on vehicle computer
Select "Engineâ€, click OK to establish vehicle communication
Select "Active Test†on the Function menu
Lots of settings are listed on Active Test menu, fuel injection, power balance, fuel pump relay etc. Select a test and accept the system notice to carry out the active test. Set the corresponding testing values to ON or OFF. Back top main function menu or click Esc to exit the program.
POSTED BY Autel Maxidas Ds708 http://www.autelmaxidasds708.net
Posted by: UOBD2autel at
06:32 AM
| No Comments
| Add Comment
Post contains 181 words, total size 3 kb.
December 31, 2015
The text below will explain how to use the wireless printing feature of originalAutel MaxiDAS DS708Automotive Diagnostic System. TheDS708scan tool is capable of printing out any graph, data, parameter ID list, or analog information directly to a personal computer connected to a printer wirelessly from anywhere in the shop.
NOTE:Your computer must be connected to the same network as yourscannerMaxiDAS DS708 wireless printing
Instruction:
Click onDS708PC SUITE V software
When you install the DS708 PC software
Click on DS708 printer application icon on your desktop
An icon similar to the software icon will appear in the lower taskbar right hand corner on your screen (see black arrow)
Double click the icon, and open sought press print
Repeat should be printed that reads test prep
Then ready to use the wireless printing feature
Connect theDS708 scannerto the wireless network
Select Setup/Help-> WIFI->Printer
Connected to your PC if you do not know how to connect your wireless network
Please click on lee Bowyer while using a tool
Go to screen you wish to print slut the camera icon in the upper right hand
A screen will open with the image file information
The same file will save to the screenshot folder on the SD card and can be accessed on a tool by going to the data managers green
Click Print button, equipment picture review slut Prince in the document will be sent to print
If you have more than one computer on the same network with Autel’s software installed, multiple "Print Servers†will display. Please click on the one you wish to pint from
Go back to review corporate see them in file by returning to the home to Crewe
Then going to data manager including on picture viewer on the top left
Click the tab recent images and you will be able to view in print
If you have any question ,please search:Autel DS708 FAQ
POSTED BY Autel Maxidas Ds708 http://www.autelmaxidasds708.net
Posted by: UOBD2autel at
02:11 AM
| No Comments
| Add Comment
Post contains 330 words, total size 5 kb.
December 30, 2015
Posted by: UOBD2autel at
01:17 AM
| No Comments
| Add Comment
Post contains 194 words, total size 4 kb.
December 29, 2015
Autel Maxidas DS708 scanner reset Audi A4 EPC light
The EPC light came on vehicle may cause car violently start shaking. Here is an instruction on reset EPC light and enable Open / Close electric parking brake of Audi A4 with theAutel MaxiDAS DS708 diagnostic scan tool.
Instruction:
Connect the MaxiDAS DS708 scanner with vehicle
Power on the DS708 system
Select vehicle region: European
Select vehicle manufacturer: Audi
Autel MaxiDAS scan tool will read the VIN automatically
Select "Maintenance function†from main function menu
Select "Electronic parking brake (EPB)â€
Turn ignition ON (very important)
Start electric parking brake and handbrake programming
Follow these steps to program:
---Start brake pad change (open brakes completely)
---Change brake pads
---End brake pad change (close brakes)
Follow the system prompts
Press "-1-†button to come to "Start brake pad change†program
Then the brakes are fully opened
Wait the brakes to be opened
Follow the system prompt, press "-2-†come to changing brake pads program
Close the brakes
Please wait the braked are locked
Fit wheels
Check the brake fluid, top it up if necessary
Brake pads replacement mode was successfully done/programmed
Back to the main menu and exit the autel ds708 software
DisconnectDS708 scanner with vehicle
Posted by: UOBD2autel at
02:14 AM
| No Comments
| Add Comment
Post contains 212 words, total size 2 kb.
31 queries taking 0.0258 seconds, 71 records returned.
Powered by Minx 1.1.6c-pink.