May 25, 2016
Recently, many customers came to ask for information about the difference of key programmersCN900andND900. Now, we customer service would like to offers you some tips about this, hope this helps you out!
Note: here we provide some free-download file:
1. CN900 auto key programmer software free download
2. ND900 auto key programmer free download
--ND900 user manual
http://www.obdtool.co.uk/upload/pro/nd900-user-manual.pdf
--ND900 updater 2.0
http://www.obdtool.co.uk/upload/pro/nd900-updater-2.0.rar
The biggest difference:
1. Copy 4D chip:
CN900 auto key programmer can copy 4D chip, but you need to buy CN900 4D Decoder for use.
ND900 auto key programmer also can copy 4D chip, but you need to buyND900 4D Decoderfor use.
2. Copy 46 chip:
CN900 can copy 46 chip only when you buyCN900 46 CLONER BOXto open theID46 authorization.
ND900 can copy 46 chip only when you buy ND900 ID46 Decoder Box to open the ID46 authorization.
CN900 & ND900 similarities:
1. Update online
--update from http://www.cn900.net/cn/pro, then you can copy 4D chip, no need to connect with the laptop.
--update from www.wugq.com.
2. Copy 4C chip
3. Cannot copy Toyota G chip, but can produce it
4. The same function:
-Identify Transponder
-Write Transponder Codes
-Copy Transponder
-Calculate eeprom memory
-Calculate Transponder Codes from eeprom memory
-Calculate pin-codes from eeprom memory, from chassis and from Transponder
-Test Transponder
-Generate Fixed Transponder Codes
-PC Software
Posted by: UOBD2autel at
07:47 AM
| No Comments
| Add Comment
Post contains 232 words, total size 4 kb.
May 24, 2016
Posted by: UOBD2autel at
07:17 AM
| No Comments
| Add Comment
Post contains 148 words, total size 6 kb.
May 21, 2016
Days ago, I used the newENET cableto manage to do some coding on BMW F22 M235i. Then, i share my coding adventure on forums. And here is one of useful feedback. Put them here and it works.
My post:
"Finally had enough time off work to get all the software installed onto my laptop (over 7GB of files). Once installed I took my newE-SYS cableand connected to the OBD II port in the car. Note, if you haven't found this connection yet it took me a while. My old E92 had a little plastic door right above the hood release, not on the F22. Everything being black I had to take a flashlight up under the driver side before I found it. No cover on it, just sits along the side kick panel above and back from the trunk release button.
Fired up the car (you can put your car on battery tender instead) and connected my new cable to the port and into the laptop. Fired up my new software (without the needed token files) and hit "connect" and prayed it would work. After two or so minutes of files loading and the LAN connection establishing communication with the car I had an active connection
Not having all the software fully licensed for use yet I did some simple looking around and check to see if my car was supported with the default F20 file set. I was able to the read my cars VIN and populate all the internal settings in the software configuration. Really cool! I now have access to all the internal data settings stored in my ECU. Save a copy of the original settings (will back them up to be safe) and shutdown. Once i get the token files I will begin finding and coding the different settings.
Pretty exciting stuff that I get to be my normal computer geek self and play with my favorite toy at the same time. Will keep this thread updated with my experience as I proceed.â€
Useful feedback:
"You don't need to be a computer software developer to install and use the software, but that won't hurt either. The reason you are finding it difficult to find all the required information and setup in one location, as best I can tell, is thata lot of what is being done could be consider in violation of warranty and/or software rights. I think the people who have ventured into this are vary worried about being exposed to the powers to be, or worst held in some legal contempt for helping others change computer settings in someone else's vehicle.
I had to make contact with no less than 3 individuals who have experience with the process and access to the software before I could even get it started. Now that I made it pass the initial issues I feel pretty good about performing these changes to my own car. I guess we will see shortly as I now have my token to perform
More Product information Please search World OBD2 Auto Diagnosis Tool Mall) www.wobd2.com
Posted by: UOBD2autel at
06:47 AM
| No Comments
| Add Comment
Post contains 533 words, total size 4 kb.
May 20, 2016
Xtool PS2 GDSis a hand-held diagnostic system covering most of gasoline heavy duty vehicles on the aftermarket. The Bluetooth PS2 diagnostic system can not only project basic diagnostic function, but support some special functions, such as oil service light, oil inspection, service mileage, service intervals and airbag. XTOOL PS2 system can be updated online.
How to update XTOOL PS2 GDSheavy duty truck diagnostic scanner?
1) First of all, go towww.xtooltech.comand login in to user center with User Name and password.
2) Select "Download Center†option under "Navigation†tab
3) Enter Download Center program, download the "Update Toolâ€
4) Then download the software you need to update
5) Save the update software to be downloaded to a certain folder
6) Open and run Xtool "Update Tool-V* exe†setup on the desktop
7) Follow the system prompt until the update tool installation is completed
After installation finished, remove the SD card from theXtool PS2 truck diagnostic tool, put the card into the SD card reader and then connect the SD card reader to the USB on your computer.
9) Open the Xtool Update Tool on the desktop when the SD card has successfully connected with your computer
10) Click the browse button to select the folder where you going to put the software winrar files.
Click Confirm button and it will reads your PS2 serial number and the software.
11) Select the software to be updated and click the "Update button†to update
12) ThePS2 GDS softwareupdate may take some time. Wait patiently until the update procedure is completed.
More Product information Please search World OBD2 Auto Diagnosis Tool Mall)www.wobd2.com
Posted by: UOBD2autel at
06:49 AM
| No Comments
| Add Comment
Post contains 276 words, total size 7 kb.
May 19, 2016
TM100 transponder key programmer v3.28has been released now. Here is the tip of TM100 update information and instruction.
TM100 V3.28release notes:
- Add keymaker for China vehicle Siemens immobox.
Parts: Immobox, IC: 93C56, Transponder: HITAG2ï¼›
2. Add keymaker for Changfeng Liebao. IC: STM8AF5288;
3. Bugs fix;
Notes:
This version includes firmware 1 update. Please DO NOT disconnect PC with TM100
while updating;
TM100 V3.26 release notes:
1. Add keymaker for Nissan TEANA as MY2012.
Parts: BCM, IC: Freescale 9S12, Transponder: PCF7952;
2. Add keymaker for Chevrolet Captiva, Silverado as MY2011.
Parts: Immobilizer Box, IC: Freescale 9S08, Transponder: PCF7936;
3. Add keymaker for Mitsubishi L200, ASX, Mirage.
Parts: EATCS, IC: EEPROM 25320, Transponder: PCF7936;
4. Fix bug: Dodge Dakota dump unknown version;
5. Add function for BMW CAS4+ save ISK;
6. Improve online activation procedure. Activation only within 10 days remaining;
How to updateTM100 Key pro
O.S.:
Windows XP(SP2 or later) Professional Version,Windows7 Ultimate and Windows 8 Professional.
Update procedure:
Press Close button after TM100 activation, you will be able to check the TM100 key pro hardware and software version information
Click ã€Update Software】button
Downloading new software from server and it will take several minutes, please wait
After that the system will display a windows prompting "File was downloaded successfully, please save your workâ€, click YES to update
Update is processing
Back to software main menu
Click Help tab
Click About to check the software that has been upgraded
More Product information Please search Best World OBD2 Auto Diagnostic ToolMall)
Posted by: UOBD2autel at
07:39 AM
| No Comments
| Add Comment
Post contains 268 words, total size 5 kb.
May 17, 2016
Posted by: UOBD2autel at
06:26 AM
| No Comments
| Add Comment
Post contains 385 words, total size 4 kb.
May 16, 2016
Audi a6l 2.4 all key lost, use Xhorse VVDI Pro and VVDI2 make key
Audi A6l 2.4all key lostand I useVVDI2 key programmerby Xhorse Company to make key and remote key successfully, the following paragraphs are the detailed procedure, hope it helps.
Remove engine from Audi a6l 2.4
Open Engine cover, find out the Engine position, disassemble engine.
Remove the engine ECU
Take apart engine ECU.
Next is to read this 95320 chip.
Remove 95320 chip and put it on theVVDI proto read data.
OpenVVDI pro
Select type, manufacture and model
Click "Newâ€
Click "Readâ€
Successfully Read out data, click "Saveâ€.
Take out chip from VVDI Pro and desoder the chip back to the engine ECU.
Reinstall engineECUback to the Audi.
Open VVDI2 and click "Audi†option.
Select "Special functionâ€
Select "EEPROM data processing toolâ€
Firstly calculate CS code
Select "ECU Simons PPDIX – Reset component protection dataâ€
Click "Load†the load the data that read out just now, then click open.
This is CS code, take a picture to record it.
Next is to calculate it’s PIN code
Select "ECU Simons PPDIX – Security Access Codeâ€
Click "Load†again to load the file.
PIN code is read out, record PIN code with photograph.
The first step is prepared well.
Open VVDI2, click "Learning Keyâ€- "Audi A6/Q7†Option.
Input the CS and PIN code that read out by VVDI pro, then you will see the button "Learning Key†and "Generate dealer key†are enabled.
Put OEM chip and 8E chip into VVDI2 key programmer.
Click "Generate dealer keyâ€
Generate dealer key is done.
Next is to learning key
Disconnect the short insurance line.
Connect back
Take out the chip fromVVDI2and put it into ignition data coil.
Click "Learning Keyâ€
Open and close car door, turn on ignition, press down brake.
Click "Learning Keyâ€.
learning successfully.
Next is to read out EZS-KESSY(J51 EEPROM.
Click "okâ€, select Chip type 9S1201128, the aim to read EZS-KESSY(J51 EEPROM is to generate OEM remote control.
Save EZS-KESSY(J51 EEPROM.
Generate OEM remote control.
Vertical put remote controller on the coil of VVDI2.
Click "Openâ€
Following the prompt the put the remote controller, click "Nextâ€
Controller is generated successfully, assembled key and to test.
Test the key whether it can start the A6L.
The car can start.
Prepare to test Remote control.
Remote control is working.
Done.
MoreVVDI Product InformationVVDI ProgPlease Search:www.wobd2.com
VVDI Key Programmer for Mercedes Benz
Source:http://blog.wobd2.com/2016/05/15/audi-a6l-2-4-all-key-lost-use-xhorse-vvdi-pro-and-vvdi2-make-key/
Posted by: UOBD2autel at
07:58 AM
| No Comments
| Add Comment
Post contains 421 words, total size 14 kb.
May 11, 2016
AutelAutoLinkAL539 OBD2/CAN SCAN TOOL
1.The AutoLinkAL539OBDII & Electrical Test Tool supports all 10 modes of OBDII test for a complete diagnosis.
2.easy-to-use AL539 will streamline automotive service and help ensure rapid, accurate diagnosis and timely repair.
3.Languages: English, German, French, Polish, Spanish
4.Support Update Online
5.Works on Almost 1996 and newer vehicles(OBDII & CAN)-domestic and import
NEXT GENERATION OBDII&CAN SCAN TOOL AutoLink AL539Internet Update Multilingual Menu
Top 3 Reasons to GetAutoLINK AL539:
1.Languages: English, German, French, Polish, Spanish
2.Support Update Online
3.Works on Almost 1996 and newer vehicles(OBDII & CAN)-domestic and import
AL539Features:
Bright color coded LEDs and built-in speaker provide both visual and audible tone for readiness verification
Weight 0.3kg (0.8lb, without wire) or 0.68kg (1.82lb, with wire)
Autel AutoLink AL539 Package Including:
Autel AutoLinkComparision
More information
Source:http://www.wobd2.com/service/autel-autolink-al539-obd2-scan-tool-535.html
Posted by: UOBD2autel at
06:42 AM
| No Comments
| Add Comment
Post contains 371 words, total size 5 kb.
May 10, 2016
1. Connect the digiprog 3 main unit into the OBD diagnostic socket, but do not use the cigar lighter lead. Otherwise, it will lose the warranty.
2. After well connect with vehicle, the digirog 3 main unit will power on, the device is loading the system.
3 Then the device screen will display digiprog III software version information. Software is marked as s unique 12 digit electronic serial number.
4. When your digiprog 3 has finished loading an information screen will appear with a disclaimer regarding the use of the machine.
5. Click "Check/Tick†button to start using the digiprog 3 odometer correction tool.
6. The digiprog 3 will require password to enter the system. The default password is "1â€.
7. Welcome the main interface. You are also allowed to check the software marked red on the picture below.
8. Select the function you need to do and follow the screen instruction.
The V4.94 digiprog 3 comes with ST01 or ST04 cable, so you do not have to buy extra cable.
For detail vehicle list and new vehicle list, please use download newly add vehicle list from WOBD2.com webpage.
NOTE:
A regulated 12 volt power supply should be used to power your digiprog III. If power up by above 13.5 volts is used to power the machine, damage may be caused to the main circuit board and it will need to be sent to your digiprog III dealer for repair.
Posted by: UOBD2autel at
06:26 AM
| No Comments
| Add Comment
Post contains 283 words, total size 4 kb.
May 09, 2016
Whenprogramanewremotekeyfor2012SUZUKIwithanewSKP900carkeyprogrammer,afterselectcorrespondingimmobilizersystem(IMMIBILIZER2)andthesystemdisplay"communicationfailedâ€errormessage.(SeeFig.1)
Thenhetriedanotherway:
Selectadaptkeyinthefunctionmenu
InsertkeyandturnignitionON
TheSKP900automotivekeyprogrammerwillreadpincodeautomatically
Manuallyenterpincode
Thesystemthendisplaystheerrormessage"Programfailedâ€whichmeansSKP900failstowritekeypincode.
Solution:
Whenprogramanewkeyremotethroughreadingpincodefromvehicle’simmobilizersystemwithSKP900autokeyprogrammer,itsupportonlyreadpincodeforvehiclethatiscompatiblewithImmobilizersystem3.Itcannotsupportimmobilizersystem1,immobilizersystem4,immobilizersystem5etc.
HereisthedetailSKP900keyprogrammervehiclelist:
http://www.WOBD2.com/upload/pro/skp-900-supported-models.pdf
Posted by: UOBD2autel at
06:49 AM
| No Comments
| Add Comment
Post contains 51 words, total size 3 kb.
May 07, 2016
OBDSTAR F100 Key programmer is a professional tool for Ford and Mazda to do mileage correction and key programming. Here is the new test of OBDSTAR F10 on Mazda 6 2013.
This is the tool to use
Source:http://www.wobd2.com/wholesale/obdstar-f-100-for-mazda-and-ford-auto-key-programmer.html
Odometer correction procedure is very easy; just follow the screen instruction.
Odometer before correction:750 19km
Select FUNCTION
Then MILEAGE ADJUSTTMENT
Then CX5
Select 2009-2013
Communication…
Input mileage of adjustment 022000
Adjusting mileage…
Adjustment complete
Mileage displayed on the dashboard now turn to220 19km
Mileage Adjustment success.
So, OBDSTAR F100 odometer correction tool performs well with Mazda. And for Ford, it also does well in terms of key programming and mileage correction.
User Guide Video
How to use OBDSTAR F100 to change km of Mazda 6 2013
Posted by: UOBD2autel at
08:55 AM
| No Comments
| Add Comment
Post contains 136 words, total size 9 kb.
May 06, 2016
Here are some tips of how to read read ecu med 17.5 withXhorse VVDI 2 commander, especially for solution of error messages "can not Access to service provider" and needing "condor automatic key cutting machine"
tool:Xhorse VVDI 2
Howto do it?:use VVDI 2 read ecu med 17.5
error message 1:
failed can not Access to service provider
error message 2(sometimes):
Get PIN, CS, MAC from internet
This function only authorize forcondor automatic key cutting machine
engineer suggestion:
this function should be performed /bound withCNC machine
More Relation Article SearchWOBD2 Official Blog
Posted by: UOBD2autel at
10:00 AM
| No Comments
| Add Comment
Post contains 101 words, total size 2 kb.
May 05, 2016
Posted by: UOBD2autel at
07:59 AM
| No Comments
| Add Comment
Post contains 34 words, total size 4 kb.
33 queries taking 0.1294 seconds, 83 records returned.
Powered by Minx 1.1.6c-pink.